We are providing Premium Quality Free Responsive Blogger Templates. Our Blogger Templates are highly professional and SEO Optimized. Detailed Garage Door Installation by 1st United Door Technologies, Inc. PURPOSE- These instructions are. Heavy- Duty residential garage. Since the installation of this garage door. If you. have any concerns about your ability to properly install this door. NOTE: All instructions are given. GETTING STARTED- Since the right tools and supplies. NOTE: Several. items are in opposite- handed pairs, and may or may not be marked. LH or RH. Hinges and track brackets should be stamped with a. Strut. counts vary by door width, height, material, gauge and track. Your door package should include the following: Door sections, one with bottom weatherstrip. Track bundle (four pieces). Hardware carton. One or more lengths of punched angle. Rollers. 10 (1. 2 on 5- sect. Cable drums. 1 pair, left and right. End bearing plates.
I bought this setup for birding. Installation was a breeze. One bit of confusion was the manual which stated the power adapters for the camera and transmitter should not be interchanged and could damage the equipment if hooked. Can be made to conform to special product needs by including appropriate addendum (like Cisco). Center bearing plate. Bottom cable/roller fixtures. Adjustable top fixtures. Cables. 2 (coiled together)9. Track flag brackets. Hole step plates*2. Bolt bag. 1*Items are used with manually operated doors only. CHECKING THE OPENING- Check the wood framing. This short piece of wood (1. If by chance you happen. Measure the garage opening. The height and width should not be appreciably. If it measures low, then the. If high or wide, then. If narrow, you run. You are now ready to set the stop. SETTING THE STOP- Tack the stop to each side. BUILDING THE SECTION- On this and the following. This. will enable you to stack the finished sections in the opening in. Lay the sections face down on a pair of sawhorses (or clean floor). The bottom section has a vinyl seal on it's lower edge, so use this. Now that you have the sections in place, you are ready to lay out. First, remove everything from the hardware. These will be used in the installation later. NOTE: All hardware in attached to the door sections. The majority. of these holes should be already drilled from the factory. Looking down on stacked sections. BOTTOM SECTION- First attach the bottom fixtures. Next, attach the. Next. slip the looped cable ends onto their studs on the bottom fixtures. Next, cut. the vinyl bottom seal to the length of the section leaving an additional. SECTION #2- Attach the #2 hinge through the pre- drilled. Next, attach #1 hinges. If you have 3. or more struts attach one just below the hinges using the above instructions. Next, put a roller into each end hinge. SECTION #3- Attach #3 hinges through the pre- drilled. Attach #1 hinges on the. If you have four struts. Next, put a roller into each end hinge. TOP SECTION- If the door has only one strut. Next, locate the top edge of the adjustable top fixture 3- 1/4. Insert. a roller into each fixture. LOCK- Since this is to be a manually operated door. Lag the snap latch exactly midway up the end stile. Drill this out to 7/8. The flange on this locking. If you tighten a screw too. Turn this inner handle clockwise as. If you are on the right end of the door, crimp. If on the left end. Crimp the other end of the cable to the snap. Crimp the aluminum oval with a pair of vise grips. You are now ready to assemble the shaft. SHAFT ASSEMBLY- From the hardware carton remove. Start the set screws. The drums are marked LH and RH. In order, slide the LH drum onto the tubular shaft, then the right. RH drum. It is possible you may only have one spring. The drum's. set screws should face inward toward the set screws in the winding. Bolt the springs together through the hole in the bearing plate. Check that the diagonal corner will be down. Attach the spring caution tag. Hand tighten the set screws to the. Torsion Spring Installation. You are now ready to assemble the track. TRACK ASSEMBLY- Separate the track bundles. For now the upper slotted hole set is ignored. Next, attach. the flag bracket through it's lower slot to the TOP most. The flanges of these three brackets should. Assemble. the vertical for the other side of the door so that when finished. Attach the horizontals to the verticals. Connect the horizontal. Align the horizontal. When tight the horizontal. Next, attach the end bearing. Tighten accordingly. Repeat for other side. When finished they should be mirror images. You are now ready to stack the door. STACKING THE DOOR- Center the bottom section. Next, using a level. Place each section in. Finally, affix hinges and rollers to each succeeding. You should now have the complete door in the opening with all rollers. It should look exactly like this. You are now ready to track the door. NOTE: -Before. tracking the door we recommend you get another person to help you. TRACKING THE DOOR- First, straighten all rollers. The track should be vertical with. With the track secured, lag down the flap bracket with three. Pull out the nails holding that side of. SPRING MOUNTING- Place the stepladder at the. Center the springs on the shaft assembly, making. Standing. at the base of the ladder, place one end of the shaft on the horizontal. Place the end. of the shaft into the end bearing plate, sliding it until the other. NOTE: -If there. is not enough clearance you may have to cut a few (no more than. With the shaft entered (equal amounts of shaft left out of the end. NOTE: -If you plan to install a garage door opener. Pre- drill two 1/4. Fasten the center bearing plate to. SETTING THE CABLES AND DRUMS- Set the LH drum. Bring the. cable up to the drum, checking for a straight run from the bottom. Set the bottom end of the cable into. Turn the drum, top toward you and down, and. Use vise grips on the shaft. Put the right hand cable in the RH drum, turning it on the shaft. The. rolling action of the set screws on this drum lends to tighten the. If the tension is OK and. If not. re- adjust the RH drum until they are close in adjustment. You are now ready to wind the springs. WINDING THE SPRINGS- The holes on the winding. They should be dressed fully into any of the holes on the spring. Stand on the ladder off to the side of the. Never stand in front. Wind the springs up. It will seem that you are trying to screw the. You wind by. inserting a bar into a hole on the casting and cranking the spring. Count the turns according to the following guide. While. firmly holding the winding bar, turn down the set screws until they. Do not touch ANY set. Remove the. vise grips and wind the other spring the same amount. If the door. seems unduly springy or . The door should rise smoothly without. You are now ready to install the back hangs. TRACK BACK- HANGS- Gently allow the door to open. Center the door in the opening. FINAL DOOR CHECK- Run the door up and down several. If you have. the steel rollers, lightly lubricate the track and the roller bearings. After the door installation is complete, adjust the stop to the. Nail the stop to the. Bolt the strike. plate to the track with track bolts. Remove this piece if you later. Adjust the clearance of the latch and plate by. Refer to Step #1. Congratulations.. You Are FINISHED!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2016
Categories |